Ingenico Lane/3000 - Configuring the Device Beep Settings
Article Contents:
Introduction to Beep Settings Adjustment, Accessing the Beep Menu for Temporary Changes, Adjusting Beep Settings: Steps and Parameters, Permanent Changes to Beep Settings, Contacting Support for Permanent Adjustments.
Step By Step:
Introduction to Beep Settings Adjustment, Accessing the Beep Menu for Temporary Changes, Adjusting Beep Settings: Steps and Parameters, Permanent Changes to Beep Settings, Contacting Support for Permanent Adjustments.
Step By Step:
Step 1: Access the Admin Menu by pressing O (the green button) to select Settings.
Step 2: Press the down arrow to scroll to the Beep option, then press O (the green button) again to select it.
Step 3: Use the number pad to input a value for Frequency (Hz). Press the down arrow to navigate and enter values for Volume, Time On (ms), and Time Off (ms). Refer to the table below for default values and acceptable ranges:- Parameter Name: Frequency (Hz)
- Default: 1,000
- Range: 20-20,000
- Description: Controls the pitch of the beep.- Parameter Name: Volume
- Default: 100
- Range: 1-100
- Description: Controls the beep volume as a percentage.- Parameter Name: Time On (ms)
- Default: 250
- Range: 10-5,000
- Description: Determines the duration of each beep.- **Parameter Name: Time Off (ms)
- Default: 250
- Range: 10-5,000
- Description: Sets the pause length between beeps.
Step 4: Press O (the green button) to finalize your adjustments. The terminal will confirm the update by displaying "Beep parameters have been updated" and emit several beeps to demonstrate the new settings.
Step 2: Press the down arrow to scroll to the Beep option, then press O (the green button) again to select it.
Step 3: Use the number pad to input a value for Frequency (Hz). Press the down arrow to navigate and enter values for Volume, Time On (ms), and Time Off (ms). Refer to the table below for default values and acceptable ranges:- Parameter Name: Frequency (Hz)
- Default: 1,000
- Range: 20-20,000
- Description: Controls the pitch of the beep.- Parameter Name: Volume
- Default: 100
- Range: 1-100
- Description: Controls the beep volume as a percentage.- Parameter Name: Time On (ms)
- Default: 250
- Range: 10-5,000
- Description: Determines the duration of each beep.- **Parameter Name: Time Off (ms)
- Default: 250
- Range: 10-5,000
- Description: Sets the pause length between beeps.
Step 4: Press O (the green button) to finalize your adjustments. The terminal will confirm the update by displaying "Beep parameters have been updated" and emit several beeps to demonstrate the new settings.
To make permanent changes to your device's beep settings, note your desired settings and contact CardPointe Support.
Related Articles
Ingenico Lane/3000 User Guide
Article Contents: This Ingenico Lane/3000 User Guide covers the device's features, setup process, and troubleshooting. It explains how to connect the device, enter text using the multi-tap method, and access the Admin Menu for advanced configuration. ...Ingenico Lane/3000 - Device Restarting Unexpectedly
Article Contents: This article explains how to correct the issue of a device unexpectedly restarting during the day, which is commonly caused by inaccurate time settings. It provides a step-by-step guide to updating your time settings on the ...Ingenico Lane/3000 Time Setting
Article Contents: To adjust the date and time in the Lane/3000 settings you will need to navigate the admin menu for the device by following the below instructions. Step By Step Guide: Step 1: Accessing and Navigating the Admin Menu. - The Admin Menu ...Ingenico Lane/3000 - Restarting The Device
Step 1: You can restart your terminal using either of the following methods: To perform a soft reboot, Access the Admin Menu and select the Restart Terminal option. To perform a hard reboot, press and hold the .,#* key and < (yellow key) ...Ingenico Lane/3000 Setting a Static IP Address for Your Device
Article Contents: Setting a static IP address for your device is optional. Typically, the device is assigned an IP address automatically when connecting to a network. To manually set the network settings for the device, follow the steps below. Access ...